| |
VERTICAL TURBINE PUMPS |
| |
FLOWMORE manufactures a board line of Vertical Turbine Pumps ranging from 100 to 2400 mm dia for capacities upto 60000 M3/Hr with heads upto 300 M. FLOWMORE Vertical Turbine Pumps are suitable for water supply, booster service, cooling towers, drainage, recirculation, airconditioning, dewatering ,process pumping, boiler-feed, petro-chemical transfer etc. In open line shaft pumps, bearings are lubricated by liquid being pumped, while enclosed line shafts with water or oil-lubrication can also be provided. Column Assemblies, both flanged and threaded are available.
Through modern design and controlled quality, bowl and impeller combinations achieve efficiencies higher than generally available for horizontal pumps.
|
|
 |
| |
By multi staging, any desired pressure can be achieved with optimum performance. Steep head capacity performance and non over-loading of driver are characteristics of these pumps. FLOWMORE enjoys a unique position of being able to recommend the construction best suited for any service requirement.
|
| |
Range: |
| |
Capacities up to 60000 M3/hr and Head up to 300 Mtrs |
| |
|
| |
Construction Features: |
| |
• Stainless steel bowl shaft and other options. |
| |
• Surface discharge head with deep stuffing box designed for extra strength. |
| |
• Cast iron / bronze / stainless-steel impellers |
| |
• Standard construction consists of cast-iron bowl, stainless steel impeller shafts, bronze or cast- iron impellers. However, any commercially available material can be furnished for specific requirements. Impeller wearing rings can be furnished for elimination of any direct wear of the impeller neck. Packing-boxes are provided commensurate with the operating pressure range of the unit. Exceptionally deep boxes with multiple packing are required and furnished for high pressure applications. Adequate provision is made for lubrication and pressure relief. Just as all the other components receive individual consideration, the packing boxes are also tailor-made to suit the duty conditions. Mechanical seals can also be furnished for highly volatile liquids This is an alternate construction to the conventional packed-box. Seals are available for low, intermediate or high pressure ranges and in a wide variety of materials of construction according to service requirement. FLOWMORE also offers a wide range of discharge heads manufactured in cast-iron or fabrication in the required metallurgy for above or below the ground level discharge branch. FLOWMORE Vertical Turbine Pumps are available with both vertical hollow shaft motors, vertical solid shaft Motors or with right-angle gear drives. With hollow drivers impeller-to-bowl clearances can be maintained with an adjusting nut at the top of the driver, while for vertical solid shaft drivers, impeller clearance is regulated with an adjusting nut in the thrust -stand assembly.
|
| |
Options: |
| • Enclosed or semi - open impellers |
| • Oil or water lubricated Shafts |
| • Deep well/short setting |
| • Underground open/ enclosed elbow |
| • Pull out construction |
| • Special alloy construction |
| |
|
| |
MATERIALS OF CONSTRUCTION FOR COMPONENTS: |
| |
Casing: CI, NICL, CF8,CF8M,CF3M,CF3NIREGIST D2,DUPLEX- 1A,DUPLEX-4A,DUPLEX -5A,WCB,NI-HARD,ALLOY-20, R-55,HASTALLOYB, HASTALLOY-C, BRONZE,CA6NM,CA15 |
| |
Impeller: CI, NICL, CF8,CF8M,CF3M,CF3NIREGIST D2,DUPLEX- 1A,DUPLEX-4A,DUPLEX -5A,WCB,NI-HARD,ALLOY-20, R-55,HASTALLOYB, HASTALLOY -C, BRONZE,CA6NM,CA15,AL. BR,PH. BR |
| |
Shaft: EN8,EN9,SS410,SS431,SS304,SS316,SS316L,SS317,KMONEL,DUPLEX |
| |
Shaft-Bearings: Cutless rubber, Neoprene, Thordon / EQVILET, Bronze, DEVCO,ORKOT |
| |
Column pipes, Enclosing Tubes, Discharge Head, Discharge Elbow, Motor Stool, Sole Plate: MS, CI,SS304,SS316,SS316L,DUPLEX |
| |
Thrust Bearing: Antifriction Ball/Roller type or Tilting pad type |
| |
Shaft seal: Gland packing, Mech. Seals |
| |
Couplings: CI, Cast steel SS410,SS304,SS316,SS316L,DUPLEX SS |
| |
Materials of construction can also be given for any other specific requirement of a client.
|
| |
Options |
| |
• Enclosed or semi - open impellers |
| |
• Oil or water lubricated Shafts |
| |
• Deep well/short setting |
| |
• Underground open/ enclosed elbow |
| |
• Pull out construction |
| |
• Special alloy construction |
| |
| |
TYPICAL APPLICATIONS: |
| |
• Water supply |
| |
• Booster service |
| |
• Cooling Tower |
| |
• Deatwering |
| |
• Recirculating service |
| |
• Irrigation |
| |
• Fire protection |
|
