FLOW MORE PUMPS

Construction Features:

Upper and lower casing dowelled for proper alignment
Oversized bearings to with stand axial and radial loads
Shaft of alloy steel with removable sleeves for better maintenance

Range Capacity : 18,000M3/hr Head :250 Mtrs

Options

Regular cast Iron, Bronze or stainless steel fitted with impeller and other options.
Single or double suction depending on size.
Can be provided with double-end shaft
Oil lubricant available
Double Impeller

HORIZONTAL SPLIT-CASE PUMPS

The Flowmore line of single stage, double suction, Split-case Centrifugal pump is representative of the broad line of Flowmore pumps serving industry.

The Flowmore lines comprises a complete family of single stage, double suction, split-case centrifugal pumps. Flowmore pumps are for high, moderate, medium and low heads. Each unit of this pump line has the same features of design and construction and the same general appearance. Available as basic unmounted pumps or with base and flexible coupling for mounting of electric motor, diesel engine, gasoline engine, steam turbine, belt drive or dual drive

IMPELLER : Impeller is one piece of cast-iron or bronze or any other material commercially available. Internal and external surfaces are carefully machined and finished to produce best possible pump performance. Impeller is for any other material commercially available pressed on the shaft over a key extending beyond the impeller so that the key also drives the shaft sleeves and prevents rotation of the sleeve on the shaft

BEARINGS AND HOUSING : Ball-bearings are of ample size to withstand all axial and radial loads imposed upon them. Bearing housings are of the cartridge type so designed to permit the entire rotating element to be removed from the pump without disturbing the alignment or exposing the bearings to dirt, water, or other contaminants. Housings are positioned by means of dowel pins in the lower half of casing.

STUFFING BOX : Stuffing Boxes are extra deep to accommodate the packing and a seal cage. The box is tapped for sealing liquid. Glands are of the split type, easily removable for repacking and are held in position by swing type glands bolts. Mechanical Rotary Seals in place of packings are available.

WEARING RINGS : Impeller Wearing rings are locked against either rotation and are machined integral with the impeller to ensure concentricity. Casing wearing rings are secured by tongue and groove fit with lower half casing.

SHAFT ASSEMBLY : Shaft is of alloy steel machined and accurately ground to size. Removable shaft sleeves provide protection against corrosive and abrasive action of the liquid pumped. Shaft sleeves are locked on the shaft by exterior sleeve nuts secured by set screws. This premits axial adjustment of the impeller.

CASING : Casing is a dense, high strength iron designed and cast to make all water passages smooth without exceesive hand finishing. Opposed dowels insure proper alignment of upper and lower casing. Bearing brackets are cast integrally to maintain accurate and permanent alignment. Provision is made for piping stuffing box leakage to drains and overflow holes are provided to protect the bearings in the events the drains become clogged. Upper half of casing is easily removed for inspection and repairs, and is so designed that entire rotating element can be removed without disturbing pipe connections or the driver.

TYPICAL APPLICATIONS:

Cooling Towers
Chilled Water Services
Condensate
General Water Supply
Municipal / Water Supply Scheme
Air Washing Circulations
Fire Service
Booster Service

MATERIALS OF CONSTRUCTION FOR COMPONENTS :

Casing: CI, NICL, CF8,CF8M,CF3M,CF3NIREGIST D2,DUPLEX- 1A,DUPLEX-4A,DUPLEX -5A,WCB,NI-HARD,ALLOY-20,
R-55,HASTALLOY-B,HASTALLOY -C, BRONZE,CA6NM,CA15

Impeller: CI, NICL, CF8,CF8M,CF3M,CF3NIREGIST D2,DUPLEX- 1A,DUPLEX-4A,DUPLEX -5A,WCB,NI-HARD,ALLOY-20, R-55,HASTALLOY-B,HASTALLOY -C, BRONZE,CA6NM,CA15,AL. BR,PH. BR

Shaft: EN8,EN9,SS410,SS431,SS304,SS316,SS316L,SS317,KMONEL,DUPLEX

Shaft-Bearings: Cutless rubber, Neoprene, Thordon / EQVILET, Bronze, DEVCO,ORKOT

Bearing: Antifriction

Shaft seal: Gland packing, Mech. Seals

Base plate: MS, CI,SS304,SS316,SS316L,DUPLEX

Couplings: CI, Cast steel SS410,SS304,SS316,SS316L,DUPLEX SS

Material of construction can also be given in any other material required by client.

DOWNLOAD PDF FILE FOR BROUCHER: